How To Install Bubble Levels On A Travel Trailer

People new to living in an RV undervalue how crucial it is to maintain level ground. Campers must be perfectly level for the components to function correctly. The question often asked is where to place levels on travel trailer to make the leveling easy and accurate.

Once you get it right, you’ll be well on your way to a good night’s sleep, and your refrigerator propane tanks will work properly. In our guide, you can learn more about bubble-level placement.

By the end, you’ll know how to get your travel trailer perfectly level with or without too much help. But, mostly, you’ll see why it makes sense to fit RV leveling bubbles, so you and the family can enjoy your vacation. (Learn How Long Does Flex Seal Last)

Install Bubble Levels On A Travel Trailer

How Level Does My RV and Travel Trailer Have To Be?

Some people in the RV world go to great lengths to attach an auto-leveling system to their trailer rather than using camper bubble levels.

For those inexperienced with leveling a trailer, the RV bubble level procedure could take longer than an hour to level front to back and side to side.

Technology that levels the playing field simplifies the entire experience. For example, self-adhesive bubble levels you may apply to your RV are highly accurate, and many electronic models let you see which stabilizer jack has to be adjusted visually.

Knowing how to carry out manual leveling is an exceptional skill, as an auto-leveling device may not work where you wish to park.

RV Leveling Mistakes

Imagine your RV as a tabletop on a center pole. The tabletop will drop if you put too much weight on one side or corner.

You may have a level back corner but an uneven front. Uneven ground and mismatched measuring devices cause this; thus, using bubble levels or a small level that monitors all four corners improves balance.

Misaligned corners affect your RV’s frame and chassis, and with repetition, you can wear and break screws, unbond glued pieces, and cause other difficulties.

How You Install RV or Trailer Bubble Levels

Flat surfaces are needed for placing your bubble levels. Most often, your driveway may be sloped, so it wouldn’t offer the best area to level your RV

Once you have an area, and after leveling your RV, 5th wheel, travel trailer, or motorhome, install your bubble levels.

Level your RV with the slide-outs in. However, trying this with the slide-outs in the out position puts stress on your stabilizer jacks.

Once appropriately positioned, your leveling jack’s work was intended.

Carpenter’s level, wheel chocks, wheel blocks, and jack pads are needed to level an RV or trailer.

RV excursions will be easier with these, and as you monitor the carpenter’s level, you’ll need some help to adjust the stabilizer jack.

To read the bubble level accurately, place it against the object you’re leveling.

If the bubble fits between the cylinder’s marks, you’re level. Bubble levels may seem inaccurate. But, despite being outdated, they’re accurate.

This step-by-step method will calibrate your leveling devices. See me level my RV in our Setup Video.

Use Wheel Chocks Before Installing Leveling Bubbles

Leveling Process to Level Travel Trailer Before Installing Leveling Bubbles

Use Wheel Chocks

You may prevent your RV from rolling by using wheel chocks. Wheel chocks provide you with that extra layer of stability even if your motorhome has a parking brake that is activated.

Use Leveling Blocks

If the ground is uneven, you must move your RV to a more level location. It could be essential to place stackable RV pads beneath one or more tires that connect like Lego bricks. (Read What Is A Tent Footprint)

Use Stabilizer Jacks

A trailer can be leveled using the stabilizer jacks. Initially, deploy them so that they touch the ground. Then, to provide them a stable foundation to connect to, put jack pads underneath their “feet.”

Use your carpenter’s level to assess how each stabilizer jack must be adjusted once all four jacks have been lowered.

Install Bubble Levels

You can calibrate your leveling devices now that you are level. Then, use the carpenter’s tool to correctly install your RV leveling devices on your motorhome.

To gain both the side-to-side and front-to-back readings in one place, many people place them in the RV’s back corner. As a result, the sidewall and rear wall are better and more precise in placement.

Best RV Leveling Devices

  • Manual Use Products: You can get chocks and blocks that do this, and one of the best is the Anderson levelers that make things easy to get the level the first time.
  • Camco EZ-Level: This four-legged device is simple. Could you put it in the RV’s midsection? Green means level; red means low. Each leg should be green. The level shuts off automatically and fits in a toolbox or other container.
  • RV Leveling Phone App: Cell phones and tablets today feature sensors that detect their orientation. RV leveling apps and most smartphones use sensors to help you balance your trailer. Some can be placed against the RV’s walls, and others on the dinette table. You’ll get a good reading either way.

Tools To Manually Level Your RV

Many RVs will not be equipped with an auto-leveling system. So, before arriving at your first campsite, you must know how to level your rig manually.

  • A bubble level
  • Blocks (you can use 2 x 6 pieces of wood as an alternative)
  • Wheel chocks (trailers often lack parking brakes, so chocks are required)

Level Your RV Left to Right

Use Your Bubble Level

  1. Try to become as level as you can from left to right while pulling into your campsite.
  2. If you have one, check your level from left to right with a big or built-in level. A big level gives more accurate readings.
  3. TIP: Your RV floor, the rear bumper, or a tabletop are all ideal locations to place your large level.
  4. Grab your set of blocks if you aren’t actual level. Pulling the RV onto blocks can raise the left or right tires to level the vehicle from left to right.
  5. To level the tires from left to right, decide if you need to raise the right or left tires.
  6. Note the angle between your trailer and the campsite. Then, decide whether rolling your RV back onto blocks or pulling it forward onto blocks is easier.
  7. Place your blocks behind the middle of your wheels if you will roll back. Then, lay the blocks in front of the wheel to pull forward.
  8. Try moving up on one block if you’re close to level. If you’re slightly off, try climbing up two blocks.
  9. Check you are now level. You might need to add another block if you haven’t reached level one yet.
  10. Build a platform to make driving up (or rolling back) on the blocks easier. For instance, use five blocks to make a ramp-like slope that goes up the height of two blocks.
  11. Don’t unhitch until you are level from left to right. Instead, take hold of your wheel chocks and place them on the wheel you didn’t raise. To prevent your camper from rolling, secure each side of the tire with a wheel chock.
  12. Now that both wheel chocks are securely in place, you can unhitch the trailer.

Tips in Installing RV Bubble Levels

Level Your RV Front to Back

  1. Grab your bubble level, but this time check the level of your RV from front to back.
  2. By lowering the tongue jack on your fifth wheel or the A-Frame jack on your travel trailer onto blocks, you can adjust the level of your RV and get it level front to back.
  3. Power jacks and hand-crank jacks both exist in jacks.
  4. Lower or install stabilizers after you get your RV level, and ensure each sits with the same pressure.
  5. If you have them, you can extend your slides now that your RV is stable and level.

How To Install RV Bubble Levels

Go out and get two RV bubble levels first. When these levels are positioned on the axis they measure for; their accuracy will be at its highest. (Read Best Way To Sleep In Tent)

For longitudinal leveling, a bubble level is placed above the axle on a single-axle bus or between the axles on a double-axle coach (Front to Back).

Many choose to place these on the passenger side of the camper trailer.

Install the bubble level on the coupler at the front (by the tongue jack) or back of the RV for latitudinal (side to side) measurements.

Behind your propane tanks at the front center, it won’t get banged and is in a good position for side leveling.

You may find some scales showing how many inches you have raised your trailer on your jacks in any given location.

Choose a Level Campsite

When you get to the campsite, pull your RV into the spot.

Check the two mounted bubble levels on your RV. Carrying a typical carpenter’s level with you can be helpful if you feel compelled to. Switch campsites if the area appears to be quite uneven. You can level a space with blocks and jacks if you discover one that is nearly level.

First, level your trailer from side to side with your connected trailer. Then, you unhitch and level the front to back when the side to side is level.

Raising RV On Leveling Blocks

Place RV leveling blocks underneath the tires on the downhill side before you unhitch.

It is suggested to use leveling blocks. Such blocks are compact enough to be stacked and robust enough to support the weight of your RV.

Inspect the tires to ensure they are centered and wholly supported by the blocks.

The tire’s sidewalls are its most vulnerable area. Make sure you block correctly to preserve your tires in the middle is the accurate location. Once the blocks are correctly positioned, carefully approach them.

Leveling with Jacks

Chock your wheels and unhitch once your RV is on the blocks.

To reduce bouncing, you will level your RV from front to rear using the front leveling jacks.

To stop your RV from rocking at each corner, now slightly extend the rear stabilizer jacks so you are as level as you can be. (Learn How Long Do Ticks Live)

Jacks for stabilizing merely help that purpose (If your RV only has stabilizer jacks, they will help stabilize and minimize bouncing but will not be helpful with leveling your rig when you park up).

However, we learned how to level with blocks and jacks, choose a great level to set up your RV, and place bubble levels.

Remember that leveling your RV properly is a great way to safeguard the tires and have a good time.

How To Install Bubble Levels On A Travel Trailer